收藏本站
ISL5216
TABLE 11. CARRIER NCO CENTER FREQUENCY UPDATE STROBE REGISTER (IWA = *006h)
P(15:0)
N/A
P(31:0)
31:0
P(31:0)
31:8
7:0
P(31:0)
N/A
P(31:0)
31
30
29
28:24
23
22
21:20
19
FUNCTION
Writing to this address generates a strobe that transfers the CCF value to the active frequency register. The transfer to the active
register can also be done using the SYNCI pin to synchronize the transfer in multiple parts or to synchronize to an external event.
TABLE 12. TIMING NCO FREQUENCY CONTROL REGISTER, MSW (IWA = *007h)
FUNCTION
These are the upper 32 bits of the 56-bit timing (resampler) NCO center frequency control.
TABLE 13. TIMING NCO FREQUENCY CONTROL REGISTER, LSW (IWA = *008h)
FUNCTION
These are the lower 24 bits of the 56-bit timing (resampler) NCO center frequency control.
Unused, set to zero.
TABLE 14. TIMING NCO CENTER FREQUENCY LOAD STROBE REGISTER (IWA = *009h)
FUNCTION
A write to this location will update the resampler NCO center frequency.
TABLE 15. FILTER COMPUTE ENGINE/RESAMPLER CONTROL REGISTER (IWA = *00Ah)
FUNCTION
μ PHold. When set, this bit stops the filter compute engine and allows the μ P access to the instruction and coefficient RAMs for
reading and writing. On the high to low transition, the filter compute engine is reset (the read and write pointers are reset and the
instruction at location 31 is fetched).
μ PShiftZeroB. This bit, when set to zero, disables the coefficient shift bits (bits 9:8 of the master register when coefficient loading).
μ PEN Limit. This bit disables the data path saturation logic. Provided for test. Active high. Set to 0 to disable the normal ROM
controlled limiting (ANDed with normal signal).
μ PZ(4:0). These bits, when set to 0, zero the corresponding read pointer address bits. This allows the pointers to be aliased, i.e.,
multiple filters can access and/or modify the same pointer. They are provided to change filters, coefficients or decimation over a
sequence.
Unused, set to 0.
Timing (resampler) NCO ENsync. If this bit is set, the center frequency is updated on a SYNCI. Set to 1.
RSRVRS(1:0). Set to 01.
Beginning/End. This bit selects whether the resampler NCO is updated at the beginning of a FIR computation or at the end of each
FIR output computation. Usually, the resampler will be updated once at the beginning of each resampler computation and this will be
bit set to 1.
1
0
Once at the beginning of the FIR instruction.
At the last tap of each of the instruction’s FIR computations (once per output).
18
RSModeSelect. This bit selects whether the resampler is a phase shifter or a frequency shifter.
0
1
Phase shift. It uses the top five bits of the timing NCO frequency to determine a phase shift and disables feedback in the timing
NCO phase accumulator—effect of the resampler is a constant phase shift.
Frequency shift. Effect of the resampler is a change in the sample rate.
17
16
15
RSCO. This bit is provided to force the resampler NCO carry when using the resampler as a phase shifter rather than for a frequency
shift. This bit must be set for phase shifting and cleared for frequency shifting. (The bit is Or-ed with the normal carry.)
RS NCO clear phase accumulator feedback on load. When this bit is set, the feedback in the resampler NCO phase accumulator is
zeroed whenever the center frequency word is updated. This forces the NCO to a known phase so the phase of multiple channels
can be aligned.
Force NCO load. This bit, when set, zeroes the feedback in the resampler NCO phase accumulator. This is provided for test or to
use the resampler for phase instead of frequency shifting.
37
FN6013.3
July 13, 2007
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ISL5217EVAL1 EVALUATION BOARD FOR ISL5217KI
ISL5239EVAL1 EVALUATION BOARD FOR ISL5239
ISL5239KIZ IC LINEARIZER PRE-DISTORT 196BGA
ISL5416EVAL1 EVALUATION PLATFORM FOR ISL5416
ISL55005IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
ISL55007IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
ISL55008IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
ISL55009IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
相关代理商/技术参数
ISL5216KI 功能描述:上下转换器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,0.8M RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5216KI-1 功能描述:上下转换器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,1.OMM PITCH BGA PACKAG RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5216KI-1Z 功能描述:上下转换器 W/ANL QD DIG DWNCNVRTR 1 OM PITCH RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5216KIZ 功能描述:上下转换器 W/ANNEAL QD DIGTL DWNCNVRTR IND TEMP RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5217 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Programmable Up Converter
ISL5217_05 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Programmable Up Converter
ISL5217EVAL1 功能描述:EVALUATION BOARD FOR ISL5217KI RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
ISL5217KI 功能描述:上下转换器 196BGA,-40+85C PROGRAMMABLE QUAD UP CONVERTER RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128